Претраживање
Приказ резултата 1-10 од 40
Structural concrete with partial or total cement replacemnet with fly ash / Konstrukcijski betoni sa delimičnom ili potpunom zamenom cementa elektrofilterskim pepelom
(Savez građevinskih inženjera Srbije, Beograd, 2015)
Building industry is facing with great challenges in directing its activities towards sustainable development. Environmental protection, the use of waste and recycled materials and reduction of the use of non-renewable ...
Experimental investigation of basic concrete properties for 3D printing technology
(Društvo za ispitivanje i istraživanje materijala i konstrukcija Srbije (DIMK)Udruženje savremene industrije glinenih proizvoda Srbije, 2022)
The aim of this paper is an experimental investigation of fresh concrete properties of the mixture designed for 3D printing. Different mixtures with and without chemical additions (superplasticizer and hydration controller) ...
Long-term behavior of composite concrete girders made continuous
(MASE, 2011)
Time-dependent effects are significant for the design of range of concrete structures. Reliable data for creep and shrinkage properties of concrete and analytical procedures are needed to account for these effects. A number ...
Effect of Mixing Approach on the Properties of Concrete with Different Aggregate Types
(Academy of Sciences and Arts of the Republic of Srpska, Bana Lazarevića 1, 78000 Banja Luka, Republic of Srpska, B&H, 2022)
The subject of the experimental tests presented in the paper is the influence of the mixing method on the physical and mechanical properties of fine-grained concrete with the nominally largest aggregate grain of 8 mm. ...
Application of 3D Concrete Printing Technology in Serbia
(Union of Mechanical and Electrotechnical Engineers and Technicians of Serbia (SMEITS) Society for Renewable Electrical Power Sources, 2023)
3D concrete printing technology represents a novel method for construction of concrete structures.
By utilizing computer systems and robotic technology, it enables optimization and automation in
construction industry. ...
Creep and shrinkage of concrete according to Eurocode 2 / Deformacije tečenja i skupljanja betona prema Evrokodu 2
(Savez inženjera i tehničara Srbije, Beograd, 2017)
This paper presents the procedure for calculation of creep coefficient and shrinkage strain according to Eurocode 2 (SRPS EN 1992-1-1:2004). The calculated values of final creep coefficient and shrinkage strain, for the ...
Effect of aggregate type and fly ash content on properties of self-compacting concrete
(Akademija nauka i umetnosti Republike Srpske, 2019)
The paper presents the results of experimental study of Self-Compacting Concrete in fresh and hardened state. Five mixtures were made, in which the content of the following components was varied: aggregates, fly ash in ...
Physical and Mechanical Properties of Concrete Cured at Low Temperatures
(Business Technical College, Uzice, 2017)
The paper reports the results of experimental tests of physical and mechanical properties of concrete which hardened in cold weather conditions without curing, without protection against precipitation and also without ...
Fiber reinforcement mortars and concretes: The possibilities of improvement physical - mechanical properties / Mikroarmirani malteri i betoni - mogućnost poboljšanja fizičko-mehaničkih svojstava
(Društvo za ispitivanje i istraživanje materijala i konstrukcija Srbije, Beograd, 2006)
Basic properties of fiber reinforcement mortar and concrete type composites have been represented in the paper. The results of authors' own laboratory testing of two concrete types as well as two mortar types are shown. ...
Experimental and theoretical analysis of timber: Concrete composite beams with mechanical connectors / Eksperimentalna i teorijska analiza spregnutih nosača drvo-beton izvedenih mehaničkim spojnim sredstvima
(Društvo za ispitivanje i istraživanje materijala i konstrukcija Srbije, Beograd, 2004)
Common needs of contemporary civil engineering put forward for constructors and architects more complex demands in the applications of new materials as well as optimal use of traditional engineering materials, with the use ...