Structural response to axial testing of cold-formed stainless steel angle columns
Чланак у часопису (Рецензирана верзија)
,
020 Elsevier Ltd.
Метаподаци
Приказ свих података о документуАпстракт
In this paper, the structural stability and compressive capacity of pin-ended cold-formed stainless steel angle columns with different slenderness were experimentally investigated. The experimental programme was performed on press-braked lean duplex stainless steel equal-leg angle sections with nominal dimensions of 80 × 80 × 4 mm, and involved material testing, initial imperfection measurements and 11 column tests. The test setup and procedure, together with the key experimental results, axial load vs. lateral deflections, axial load vs. torsional rotations and characterised failure modes, were fully reported and analysed. The experimental observations reveal that the failure mode type, including local/torsional, flexural-torsional and flexural effects, is highly dependent on the column's slenderness and initial imperfections. The measured compressive strengths were compared with the resistance predictions determined according to European and Australia/New Zealand codified design proc...edures. It was found that experimentally obtained ultimate capacities are significantly higher than those calculated according to the specifications. However, the database of test results is still quite limited, and a further research is needed to amplify the data needed to enable a more precise assessment of the codified procedures.
Кључне речи:
Experiment / Equal-leg angle section / Cold-formed / Flexural-torsional buckling / Flexural buckling / Stainless steelИзвор:
Thin-Walled Structures, 2020, 156Финансирање / пројекти:
- Истраживање стања и метода унапређења грађевинских конструкција са аспекта употребљивости, носивости, економичности и одржавања (RS-MESTD-Technological Development (TD or TR)-36048)
Институција/група
GraFarTY - JOUR AU - Dobrić, Jelena AU - Filipović, Aljoša AU - Marković, Zlatko AU - Baddoo, Nancy PY - 2020 UR - https://grafar.grf.bg.ac.rs/handle/123456789/2096 AB - In this paper, the structural stability and compressive capacity of pin-ended cold-formed stainless steel angle columns with different slenderness were experimentally investigated. The experimental programme was performed on press-braked lean duplex stainless steel equal-leg angle sections with nominal dimensions of 80 × 80 × 4 mm, and involved material testing, initial imperfection measurements and 11 column tests. The test setup and procedure, together with the key experimental results, axial load vs. lateral deflections, axial load vs. torsional rotations and characterised failure modes, were fully reported and analysed. The experimental observations reveal that the failure mode type, including local/torsional, flexural-torsional and flexural effects, is highly dependent on the column's slenderness and initial imperfections. The measured compressive strengths were compared with the resistance predictions determined according to European and Australia/New Zealand codified design procedures. It was found that experimentally obtained ultimate capacities are significantly higher than those calculated according to the specifications. However, the database of test results is still quite limited, and a further research is needed to amplify the data needed to enable a more precise assessment of the codified procedures. T2 - Thin-Walled Structures T1 - Structural response to axial testing of cold-formed stainless steel angle columns VL - 156 DO - https://doi.org/10.1016/j.tws.2020.106986 ER -
@article{ author = "Dobrić, Jelena and Filipović, Aljoša and Marković, Zlatko and Baddoo, Nancy", year = "2020", abstract = "In this paper, the structural stability and compressive capacity of pin-ended cold-formed stainless steel angle columns with different slenderness were experimentally investigated. The experimental programme was performed on press-braked lean duplex stainless steel equal-leg angle sections with nominal dimensions of 80 × 80 × 4 mm, and involved material testing, initial imperfection measurements and 11 column tests. The test setup and procedure, together with the key experimental results, axial load vs. lateral deflections, axial load vs. torsional rotations and characterised failure modes, were fully reported and analysed. The experimental observations reveal that the failure mode type, including local/torsional, flexural-torsional and flexural effects, is highly dependent on the column's slenderness and initial imperfections. The measured compressive strengths were compared with the resistance predictions determined according to European and Australia/New Zealand codified design procedures. It was found that experimentally obtained ultimate capacities are significantly higher than those calculated according to the specifications. However, the database of test results is still quite limited, and a further research is needed to amplify the data needed to enable a more precise assessment of the codified procedures.", journal = "Thin-Walled Structures", title = "Structural response to axial testing of cold-formed stainless steel angle columns", volume = "156", doi = "https://doi.org/10.1016/j.tws.2020.106986" }
Dobrić, J., Filipović, A., Marković, Z.,& Baddoo, N.. (2020). Structural response to axial testing of cold-formed stainless steel angle columns. in Thin-Walled Structures, 156. https://doi.org/https://doi.org/10.1016/j.tws.2020.106986
Dobrić J, Filipović A, Marković Z, Baddoo N. Structural response to axial testing of cold-formed stainless steel angle columns. in Thin-Walled Structures. 2020;156. doi:https://doi.org/10.1016/j.tws.2020.106986 .
Dobrić, Jelena, Filipović, Aljoša, Marković, Zlatko, Baddoo, Nancy, "Structural response to axial testing of cold-formed stainless steel angle columns" in Thin-Walled Structures, 156 (2020), https://doi.org/https://doi.org/10.1016/j.tws.2020.106986 . .